[DIY Part 1] Building a MIDIbox SEQ v4+ (midiphy.com video tutorial) MP3

[DIY Part 1] Building a MIDIbox SEQ v4+ (midiphy.com video tutorial) MP3

Download song [DIY Part 1] Building a MIDIbox SEQ v4+ (midiphy.com video tutorial) MP3 you can download it for free at Loopa Download Music. Song details [DIY Part 1] Building a MIDIbox SEQ v4+ (midiphy.com video tutorial) can you see the table, for the download link [DIY Part 1] Building a MIDIbox SEQ v4+ (midiphy.com video tutorial) is below.

Title [DIY Part 1] Building a MIDIbox SEQ v4+ (midiphy.com video tutorial)
Duration 02:07
File Format mp3
Mime Type audio/mpeg
Bitrate 128 kbps
Size 2.91 MB
Views 5,030x
Uploaded on 27 Juli 2018

Please click one of the buttons that works, if the download has not started, please click again until you can 😘

Download Mp3

Welcome to the first part of the video build tutorial of the new MIDIbox SEQ v4+!
[ UPDATES/ERRATA - IMPORTANT! ]
wCore PCB Version 1.5 and up: contains a new PolyFuse (PF1), that is relevant only for USB OTG. Please don't forget to install it, it comes with your BOM!
9:54 - In the chapter overview screen, R3 should be listed as 330R, not 33R (correct in the BOM and later on in the audio comment) - Thanks, Tom!
56:20 - Make sure your switch on the USB board is in the up position. Thanks, Jeremy!
1:35:18 - use 20 MHz crystals for the PIC 16F88s! Value/part in the BOM has been corrected.
1:37:00 - the 100N caps are for C3, C6, C9, C12 (not C1-C4). The BOM was correct. Thanks, Keir!

This is a detailed step-by-step build video tutorial with additional notes, tips and tricks. While the SEQv4+ build is targeted towards intermediate DIYers, it is our firm belief, that everyone being able to hold a soldering iron with a fine soldering tip should have a fair chance of building it, therefore the detailed documentation.

Please refer to the above UPDATES/ERRATA and the below NOTES sections before starting building, in case some some errors did sneak into the video - thanks! :)

[ CHAPTER TIMETABLE ]
0. Overview and Introduction 00:00
1. wCore: Breaking it up (optional for non-SEQ v4+ builds) 05:42
2. wCore: SMT Capacitors 07:15
3. wCore: SMT Resistors 09:52
4. wCore: SMT TVS Diode 12:06
5. wCore: SMT ICs 14:29
6. wCore: THT Diodes 21:10
7. wCore: THT Resistors 23:34
8. wCore: THT Transistors 26:45
9. wCore: THT Potentiometers 32:09
10. wCore: MCU Headers: 34:10
11. wCore: Pin Headers 35:47
12. wCore: IDC Shrouded Headers: 37:15
13. wCore: Installing USB PCB Connectors 40:10
14. wCore: (Re)connecting Core and USB PCB 46:50
15. wCore: Prepare the Waveshare MCU 51:45
16. wCore: Waveshare MCU Jumper Config 55:41
17. wCore: MIOS Studio: uploading MBSEQ App 56:18
18. SD Card: Building the SD Card PCB 57:54
19. SD Card: Building an IDC ribbon connector cable 1:11:03
20. MIDI8: THT Diodes and Resistors 1:13:57
21. MIDI8: Installing IC Sockets 1:18:09
22. MIDI8: Installing Pin Headers & Shrouded IDC Headers 1:20:10
23. MIDI8: Installing PCB to Case Fasteners 1:22:43
24. MIDI8: Installing BLM and MIDI Sockets 1:23:42
25. MIDI8: Installing Optocouplers 1:30:12
26. I2C: Installing THT Resistors 1:31:05
27. I2C: Installing PIC IC Sockets 1:33:35
28. I2C: Installing Crystals 1:35:10
29. I2C: Installing THT Capacitors 1:36:34
30. I2C: Installing THT Capacitors (Part 2) 1:37:55
31. I2C: Installing PCB to Case Fastners 1:39:44
32. I2C: Installing Shrouded 10-pin IDC Header 1:40:39
33. I2C: Installing MIDI Sockets 1:41:21
34. I2C: Installing the PICs (16F88) 1:43:34
35. LineTX/RX: Installing the IC Sockets 1:45:26
36. LineTX/RX: THT Capacitors 1:46:25
37. LineTX/RX: Installing Gold Pinheaders: 1:47:56
38. LineTX/RX: THT Resistors: 1:50:12
39. LineTX/RX: Shrouded 10-pin IDC Headers 1:53:37
40. LineTX/RX: DB25 Sockets 1:54:52
41. LineTX/RX: Mounting ICs 1:57:17
42. Epilogue 2:01:40

[ FULL BILL OF MATERIALS ]
https://www.midiphy.com/en/shop-details/137/1/midibox-core-pcbs-essential-kit#bom

[ SHOP LINK TO PCB KIT ]
https://www.midiphy.com/en/shop-details/137/1/midibox-core-pcbs-essential-kit

[ NOTES ]
1. 1:18:45 and 1:33:46 Regarding low/high quality IC sockets: in the tutorial, we described the used PIC 16F88 IC sockets to be "high quality". But, the consensus is that although the IC pins cut into the socket (maybe making a better connection?) the "pro" advice is that the dual-wipe type are generally better. In short: both types will work out, if you have one type or the other, you will be good within the SEQv4+ application/usecase.

------------------------------------------------------------

Hope you enjoyed the build! :) We are already working on the second and final part of the tutorial, but have to wait for the final production case (including labels) to arrive, needs a bit more time, expect it to be in late summer/early autumn 2018! If you want to build a SEQv4+, you could already start with the PCBs built in this first tutorial, as you will need them for your v4+. Have fun!

Many greets and thanks for watching and listening!
Peter/Hawkeye

Tags: #midiphy #MIDIbox #SEQv4+ #SEQv4 #Sequencer #DIY #Build #Soldering #Video #Tutorial #v4 #MIDI #hardware sequencer #dawless #do it yourself #dream it yourself